press brake - CNC

AD-SERVO

Eco-friendly press brake for clean energy saving operations.  Lower cost, energy efficient, accurate, speed and quiet.

  • 60 % in 1 hour with 15 press cycles

  • Supports your production cost efficiency and increases your

  • competitive forces.

  • Small hydraulic oil tank for Clean environment & Cost reduction

  • Thanks to the new technology reduce hydraulic tank from 200 lt to 2x40 lt

  • Speeds & Accuracy & Syncronisation

  • Beam speeds to 200mm/sec

  • 5,6 times better Synchronisation in phase of „High Speed“

  • Increase your competitive forces by 62% lower power consumption

  • Lower cost per part by ecologic technology

  • Quiet, Energy Efficient and Accurate

  • Ram movement is powered by AC Servo motors driving hydraulic oil in line with Variable Speed Pump. New technology allows : Silent bends, Noise level reduced to 63 dbA from 76 dbA, Energy save, 62% at stand-by.

  • 44% during the press cycle

Standard Features

  • Y1, Y2, X, R - 4-Axes

  • Control Unit - CNC Cybelec ModEva 10S 3D with PC 1200 3D SW or Delem 66W

  • CNC controlled motorized Crowning

  • CNC controlled Hyd-Mech Crowning ( Standard - 800 t )

  • European Clamping system ( Standard - 400 t )

  • DURMA Clamping system ( Standard - 600 t )

  • Sliding Front Arms with full length linear guide

  • Back gauge , Servo-motorised & Linear guide & Ball bearing system ( X- R )

  • Sliding sheet support Arms with T-Canal and Tilting stop

  • Protection covers

  • Special designed - worldclass hydraulics blocks & valves

  • Worldclass electronics system

Features

Syncro Y1Y2 Axes & CNC Control Motorized Crowning Independent left and right axes (Y1Y2) controlled by electronics servo valves & electronics linear position controllers. CNC controlled motorized crowning system homogenizes bending forces every points of the bending parts to acquire straights bents. The need for shimming is eliminated

Syncro Y1Y2 Axes & CNC Control Motorized Crowning
Independent left and right axes (Y1Y2) controlled by electronics servo valves & electronics linear position controllers. CNC controlled motorized crowning system homogenizes bending forces every points of the bending parts to acquire straights bents. The need for shimming is eliminated

Sliding front arms Quickset support arms are mounted on a linear quide way and ball bearing system that allows “finger tip” lateral adjustment of the front support arms. Vertically adjustment is also easily achieved

Sliding front arms
Quickset support arms are mounted on a linear quide way and ball bearing system that allows “finger tip” lateral adjustment of the front support arms. Vertically adjustment is also easily achieved

X-R Back gauge Fingers` depth and height is calculated by CNC controller and executes high speed servo motors produced by Siemens. Retraction is also a standard feature to acquire accurate parts. Back gauge fingers are easily adjusted on linear guides by ball integrated motion system

X-R Back gauge
Fingers` depth and height is calculated by CNC controller and executes high speed servo motors produced by Siemens. Retraction is also a standard feature to acquire accurate parts. Back gauge fingers are easily adjusted on linear guides by ball integrated motion system

High Stroke / Daylight / Throat = High working space AD-S machines offers wide spaces for ease of operation also reduces cycle times

High Stroke / Daylight / Throat = High working space
AD-S machines offers wide spaces for ease of operation also reduces cycle times

Tool Systems

Eurostyle clamping Eurostyle tool holders offers precise tool setup by their ground surfaces

Eurostyle clamping
Eurostyle tool holders offers precise tool setup by their ground surfaces

Hydrolic new standard clamping

Hydrolic new standard clamping

Eurostyle clamping

Eurostyle clamping

Durma tool clamping

Durma tool clamping

Quick release clamping

Quick release clamping

Durma hydraulic clamping

Durma hydraulic clamping

Hydrolic eurostyle clamping

Hydrolic eurostyle clamping

Optional Features

  • CE with FIESSLER AKAS-LC II F manual + AKFR control box
  • CE with FIESSLER AKAS-LC II AKAS-3 M Motorised + FPSC (SAFETY PLC)
  • CE with SICK C 4000- only for tandem
  • DFS1 Laser Finger protection ( for Bottom Beam-Non CE )
  • Z1, Z2 Axes
  • X1, X2 Axes
  • R1, R2 Axes
  • R1 R2 axes on the finger blocks
  • Delta X axis ,+250mm stroke
  • X Axis =1000 mm - Back protection with Light barrier
  • X1 X2 Axes = 1250 mm - for lighting pole
  • X1 X2 Axes = 1250 mm - for lighting pole - pneumatic pushers
  • AP3-AP4 Sheet follower with sliding guide- Motorised height adj
  • F1-F2 Front feeding system with supports
  • F1-F2 Front feeding system with supports - pneumatic pushers
  • Quick Release Clamping
  • Durma Hydraulic or Mechanical Clamping
  • Wila Hydraulic or Mechanical Clamping
  • Tool options ( Durma, European, Wila ) in tool catalog
  • Bottom tool separation system
  • Crowning Vertical

BACK GAUGE OPTIONS

X, R, Z1, Z2 4 Axes

X, R, Z1, Z2 4 Axes

X1, X2, R, Z1, Z2, 5 Axes

X1, X2, R, Z1, Z2, 5 Axes

X1, X2, R1, R2, Z1, Z2, 6 Axes

X1, X2, R1, R2, Z1, Z2, 6 Axes

Delta X

Delta X

BACK GAUGE FINGERS

 
3 Steps finger blocks

3 Steps finger blocks

Special fingers

Special fingers

 

BOTTOM TOOL POSITIONING SYSTEMS

Laser angle measurement system Manufacturing sheet metal parts with properly bending angles that are kept constant all times often meets a problem during the actual production process: different parameters in material  thickness and stresses. The best solution is laser based bending angle measuring device.  Any bending angle can be measured Very compact, everything in the appliance Light influence, light or dark material surfaces play practically no part at all

Laser angle measurement system
Manufacturing sheet metal parts with properly bending angles that are kept constant all times often meets a problem during the actual production process: different parameters in material  thickness and stresses. The best solution is laser based bending angle measuring device. 

Any bending angle can be measured
Very compact, everything in the appliance
Light influence, light or dark material surfaces play practically no part at all

Pneumatic positioning system

Pneumatic positioning system

Motorized positioning system

Motorized positioning system

CNC Control Unit

ModEva 10S 3D & Pc 1200 3D S W ModEva is a range of numerical controls adapted to the actual market demand. Therefore the complete ModEva serie runs now under Windows ModEva can provide a calculating capacity and performance adapted to simple machinery with a 3D graphic display, it can also be transformed into a real workstation with a very high-power CPU and maximum graphic capabilities thus making Cybelec ® adapted numerical control available to the most sophisticated machinery. All ModEvaTM consoles are equipped with the new Quick CursorTM device. One of its main features is the possibilty of completely programming a part on a single page. When producing more complex parts, the graphic sequences generated by a CAD/CAM system can easily be viewed on the user console. All ModEva come with PC 1200 off line bending software. PC 1200 program allows you to prepare your programs, calculate offers and check feasibility of the parts in your Office on a PC. No time waisted on the machine. 3D / 10,4” color screen TFT type screen 128 Mb Ram 128 DM Main Memory Easy Cursor Automatic Bend Sequences PC Off line 3D Software

ModEva 10S 3D & Pc 1200 3D S W
ModEva is a range of numerical controls adapted to the actual market demand. Therefore the complete ModEva serie runs now under Windows ModEva can provide a calculating capacity and performance adapted to simple machinery with a 3D graphic display, it can also be transformed into a real workstation with a very high-power CPU and maximum graphic capabilities thus making Cybelec ® adapted numerical control available to the most sophisticated machinery.

All ModEvaTM consoles are equipped with the new Quick CursorTM device. One of its main features is the possibilty of completely programming a part on a single page. When producing more complex parts, the graphic sequences generated by a CAD/CAM system can easily be viewed on the user console.

All ModEva come with PC 1200 off line bending software. PC 1200 program allows you to prepare your programs, calculate offers and check feasibility of the parts in your Office on a PC. No time waisted on the machine.

3D / 10,4” color screen
TFT type screen
128 Mb Ram
128 DM Main Memory
Easy Cursor
Automatic Bend Sequences
PC Off line 3D Software

ModEva RA 3D / 15” color screen TFT type screen 128 Mb 256/512 Ram 20 GB Main Memory Easy Cursor Automatic Bend Sequences PC Off line 3D Software

ModEva RA
3D / 15” color screen
TFT type screen
128 Mb 256/512 Ram
20 GB Main Memory
Easy Cursor
Automatic Bend Sequences
PC Off line 3D Software

Delem DA 66T The DA-66T is the Delem modular press brake controller. All graphics, including product and machine as well as tool setup are also available in 3D. This to visualize the machine situation as accurate as possible. The DA-66W can program 2D products, accurately showing and calculating including sheet thickness and radii. During programming automatically generation of bend sequencers can be used as well as manual selection. The operator can overrule to his own choice. With the DA-66W also special tools for e.g. hemming bends can be programmed. The DA-66W helps the user in programming these bends (with their specific parameters) and also shows the prebend as well as the hemming operation during production.

Delem DA 66T
The DA-66T is the Delem modular press brake controller. All graphics, including product and machine as well as tool setup are also available in 3D. This to visualize the machine situation as accurate as possible. The DA-66W can program 2D products, accurately showing and calculating including sheet thickness and radii. During programming automatically generation of bend sequencers can be used as well as manual selection. The operator can overrule to his own choice. With the DA-66W also special tools for e.g. hemming bends can be programmed. The DA-66W helps the user in programming these bends (with their specific parameters) and also shows the prebend as well as the hemming operation during production.

Delem DA 69T The DA-69T is 1:1 compatible with the DA-66W and offers next to 2D products also 3D products. 3D products can be programmed with accurate sheet thickness and desired radii. Automatical bend sequence calculation can help finding the optimum bend sequence even from very complex products. Multiple products can programmed in 3D, 2D as well as numerical. Storage is managed on the CF-harddrive. The controllers Windows operating system enabled easy integration in factory networks and due to the real-time capable OS, also instant switch of is possible. The controller will start-up time after time, without annoying booting messages. The DA-66W and DA-69W can also be equipped with an optional touch screen.

Delem DA 69T
The DA-69T is 1:1 compatible with the DA-66W and offers next to 2D products also 3D products. 3D products can be programmed with accurate sheet thickness and desired radii. Automatical bend sequence calculation can help finding the optimum bend sequence even from very complex products. Multiple products can programmed in 3D, 2D as well as numerical. Storage is managed on the CF-harddrive. The controllers Windows operating system enabled easy integration in factory networks and due to the real-time capable OS, also instant switch of is possible. The controller will start-up time after time, without annoying booting messages. The DA-66W and DA-69W can also be equipped with an optional touch screen.

Machine Specs

 

DURMA AD-S T 12800 Press Brake Machine (Tandem)

- Loading Unloading System

- Front Feeding System with Pnematic Pushers

- Light Pole Industry - Unmanned Production