DUAL OPERATOR SERIES

iron worker

This series has two independent hydraulic systems, therefore one person can be punching while a second is cropping.

Standard Features

  • 60 - 88 - 121 - 188 Tons
  • Five Stations
  • Dual Cylinder Operation

Features

  Angle Cutting  Blades are four sided and easily installed and rotated. The cavity is designed in such a way to allow the mitering of angles. An easy adjustable hold down provides for proper clamping of the material while it is being sheared. Shown with special Z aperture on 45 M.

Angle Cutting
Blades are four sided and easily installed and rotated. The cavity is designed in such a way to allow the mitering of angles. An easy adjustable hold down provides for proper clamping of the material while it is being sheared. Shown with special Z aperture on 45 M.

  Angle Station  The angle cavity is equipped with an easily adjustable hold down to increase sheared blank quality.

Angle Station
The angle cavity is equipped with an easily adjustable hold down to increase sheared blank quality.

  Angle Mitering  The angle station allows mitering at 45 degrees. The capacity is less than the 90° mitering capabilities.

Angle Mitering
The angle station allows mitering at 45 degrees. The capacity is less than the 90° mitering capabilities.

  Angle Mitering & Flat Bar Station  It is possible to miter the leg of an angle at 5° in the flat bar shear station.

Angle Mitering & Flat Bar Station
It is possible to miter the leg of an angle at 5° in the flat bar shear station.

  Large Throat & Gauging Table  A large throat and gauge table is standard on the dual cylinder models. The table is equipped with recessed measuring scales calibrated to the center line of the punch. Side and rear gauge stops are also included. A larger throat is available as an option and a 24” throat is standard on the 120 ton models.

Large Throat & Gauging Table
A large throat and gauge table is standard on the dual cylinder models. The table is equipped with recessed measuring scales calibrated to the center line of the punch. Side and rear gauge stops are also included. A larger throat is available as an option and a 24” throat is standard on the 120 ton models.

  Swing Away Stripper  A swing away style punch stripper allows proper stripping of the part. It is easily moved away for greater access to the punch and die area

Swing Away Stripper
A swing away style punch stripper allows proper stripping of the part. It is easily moved away for greater access to the punch and die area

  Channel Web Punching  The specially shaped punch station bolster allows punching holes in the web of profiles.

Channel Web Punching
The specially shaped punch station bolster allows punching holes in the web of profiles.

  Flat Bar Shearing  An easily adjustable hold down ensures proper clamping of the plate. An entry feed table has adjustable guides and stops to make sure the material is accurately placed under the cutting blades. The blades are manufactured in such a way that allows cutting of a wide range of material thickness at a low rake angle and without the need for adjustment

Flat Bar Shearing
An easily adjustable hold down ensures proper clamping of the plate. An entry feed table has adjustable guides and stops to make sure the material is accurately placed under the cutting blades. The blades are manufactured in such a way that allows cutting of a wide range of material thickness at a low rake angle
and without the need for adjustment

  Notching  This station comes standard with rectangular notching blades which allow side notching, therefore allowing notching of unlimited widths. Vee notching blades can easily be installed, and are available as an option.

Notching
This station comes standard with rectangular notching blades which allow side notching, therefore allowing notching of unlimited widths. Vee notching blades can easily be installed, and are available as an option.

  Touch & Cut Electrical Back Stop  39” back stop with electrical touch and cut feature that aligns to all shearing stations.

Touch & Cut Electrical Back Stop
39” back stop with electrical touch and cut feature that aligns to all shearing stations.

  Optional Press Brake Attachment  It is possible to mount a bending attachment to the punch station. A large single vee or a four vee for thinner material is available.

Optional Press Brake Attachment
It is possible to mount a bending attachment to the punch station. A large single vee or a four vee for thinner material is available.

Machine Specs

Product video